VWIC-2MFT-E1-DI looks like its dead! Help...

Submitted by londonnet on Tue, 08/12/2008 - 12:21

Cisco CallManager Express

Good day. I have a c1760 with two DSP 8's and a VWIC-2MFT-E1-DI

I can see the card listed in the correct slot when perfor a show inve and I can see a voice card entry in the show run but thats it.

Can't see any interfaces or controllers.

Is there some extra commands I need to run to get the controllers to show so I can then configure them?

What are the steps to configuring the interface from installing the card and powering on?

Average:

Your rating: None


	#1Submitted by dhooper on Wed, 08/13/2008 - 23:12. What does 'controller E1 What does 'controller E1 0/0' (or what ever slot it's in) bring up when you type it into config mode? Maybe just the IOS doesnt support it. Login or register to post comments


	#2Submitted by londonnet on Tue, 08/12/2008 - 16:29. Is there a command to reset Is there a command to reset the card to defaults? I now that some cards carry config on them. Login or register to post comments


	#3Submitted by londonnet on Tue, 08/12/2008 - 16:28. Thanks for the reply. I had Thanks for the reply. I had looked at thease settings but sadley the commonds are missing. I can see the card in the show inve but not in the show ver below is a truncated show tech if anyone is brave to take a look pbx03#show tech ------------------ show version ------------------ Cisco IOS Software, C1700 Software (C1700-ADVIPSERVICESK9-M), Version 12.4(9)T7, RELEASE SOFTWARE (fc3) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2008 by Cisco Systems, Inc. Compiled Thu 10-Jan-08 14:54 by prod_rel_team ROM: System Bootstrap, Version 12.2(7r)XM2, RELEASE SOFTWARE (fc1) pbx03 uptime is 18 hours, 21 minutes System returned to ROM by power-on System restarted at 01:34:17 BST Tue Aug 12 2008 System image file is "flash:c1700-advipservicesk9-mz.124-9.T7.bin" This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption. Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately. A summary of U.S. laws governing Cisco cryptographic products may be found at: http://www.cisco.com/wwl/export/crypto/tool/stqrg.html If you require further assistance please contact us by sending email to export@cisco.com. Cisco 1760 (MPC860P) processor (revision 0x500) with 120241K/10831K bytes of mem ory. Processor board ID FOC08270PX3 (453088369), with hardware revision 0000 MPC860P processor: part number 5, mask 2 1 FastEthernet interface 1 Serial(sync/async) interface 2 Voice FXO interfaces 2 Voice FXS interfaces 32K bytes of NVRAM. 32768K bytes of processor board System flash (Read/Write) Configuration register is 0x2102 ------------------ show running-config ------------------ Building configuration... Current configuration : 5429 bytes ! ! Last configuration change at 19:10:38 BST Tue Aug 12 2008 ! version 12.4 service tcp-keepalives-in service tcp-keepalives-out service timestamps debug datetime msec service timestamps log datetime msec service password-encryption service sequence-numbers ! hostname pbx03 ! boot-start-marker boot system flash c1700-advipservicesk9-mz.124-9.T7.bin boot-end-marker ! enable password 7 ! no aaa new-model ! resource policy ! clock timezone GMT 0 clock summer-time BST recurring voice-card 1 ! voice-card 2 codec complexity medium ! voice-card 3 codec complexity medium ! ip cef ! ! ! ! ip domain name towerbridge.com ip name-server 212.158.248.6 ip name-server 212.158.248.5 ! ! ! ! voice service voip clid network-provided allow-connections h323 to h323 allow-connections h323 to sip allow-connections sip to h323 allow-connections sip to sip no supplementary-service h450.2 no supplementary-service h450.3 supplementary-service h450.12 h323 sip registrar server expires max 3600 min 3600 ! ! voice class codec 1 codec preference 1 g711alaw codec preference 2 g711ulaw codec preference 3 g729r8 ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface FastEthernet0/0 ip address 172.16.1.11 255.255.255.0 speed auto ! interface Serial0/0 no ip address shutdown ! ip route 0.0.0.0 0.0.0.0 172.16.1.1 ! ! ip http server no ip http secure-server ! ! ! ! tftp-server flash:P0030702T023.bin tftp-server flash:P0030702T023.sbn tftp-server flash:CP7905080001SCCP051117A.sbin tftp-server flash:CP7905080001SCCP051117A.zup tftp-server flash:P0030702T023.loads tftp-server flash:P0030702T023.sb2 tftp-server flash:DistinctiveRingList.xml tftp-server flash:Analog1.raw tftp-server flash:Analog2.raw tftp-server flash:AreYouThere.raw tftp-server flash:AreYouThereF.raw tftp-server flash:Bass.raw tftp-server flash:CallBack.raw tftp-server flash:Chime.raw tftp-server flash:Classic1.raw tftp-server flash:Classic2.raw tftp-server flash:ClockShop.raw tftp-server flash:Drums1.raw tftp-server flash:Drums2.raw tftp-server flash:FilmScore.raw tftp-server flash:HarpSynth.raw tftp-server flash:Jamaica.raw tftp-server flash:KotoEffect.raw tftp-server flash:MusicBox.raw tftp-server flash:music-on-hold.au tftp-server flash:Piano1.raw tftp-server flash:Piano2.raw tftp-server flash:Pop.raw tftp-server flash:Pulse1.raw tftp-server flash:Ring1.raw tftp-server flash:Ring2.raw tftp-server flash:Ring3.raw tftp-server flash:Ring4.raw tftp-server flash:Ring5.raw tftp-server flash:Ring6.raw tftp-server flash:Ring7.raw tftp-server flash:RingList.xml tftp-server flash:Sax1.raw tftp-server flash:Sax2.raw tftp-server flash:Vibe.raw ! control-plane ! ! ! voice-port 2/0 supervisory disconnect dualtone mid-call input gain 10 output attenuation -6 no comfort-noise cptone GB timeouts call-disconnect 5 timeouts wait-release 5 connection plar opx 3011 description Bulldog ! voice-port 2/1 supervisory disconnect dualtone mid-call input gain 10 output attenuation -6 no comfort-noise cptone GB timeouts call-disconnect 5 timeouts wait-release 5 connection plar opx 3012 description Free FXO ! voice-port 3/0 ring cadence pattern12 cptone GB ! voice-port 3/1 ! ! ! ! ! ! dial-peer voice 3005 pots description For Cordless destination-pattern 3005 port 3/0 ! dial-peer voice 3006 pots description For Cordless destination-pattern 3006 port 3/1 ! dial-peer voice 9 pots description External call To PSTN destination-pattern 9T port 2/0 ! ! telephony-service fxo hook-flash load 7960-7940 P0030702T023 load 7905 CP7905080001SCCP051117A max-ephones 16 max-dn 32 ip source-address 172.16.1.11 port 2000 service phone displayIdleTimeout 00:30 service phone displayOnDuration 1:00 service phone videoCapability 1 service phone settingsAccess 1 service phone daysDisplayNotActive 1,2,3,4,5,6,7 service phone displayOnTime 09:00 timeouts interdigit 4 system message PBX03 url services http://phone-xml.berbee.com/menu.xml network-locale GB time-zone 21 date-format dd-mm-yy mwi relay max-conferences 4 gain -6 moh music-on-hold.au web admin system name admin password neverb dn-webedit time-webedit transfer-system full-consult secondary-dialtone 9 directory last-name-first create cnf-files version-stamp 7960 Aug 12 2008 01:33:28 ! ! ephone-dn 1 dual-line number 3001 pickup-group 1 label 3001 description Lounge name 3001 hold-alert 30 originator ! ! ephone-dn 2 dual-line number 3002 pickup-group 1 label 3002 description Kitchen name 3002 hold-alert 30 originator ! ! ephone-dn 3 number 3003 description SoftPhone name 3003 hold-alert 30 originator ! ! ephone-dn 10 number 3010 name IP-Paging1 paging ip 239.1.1.1 port 2000 ! ! ephone-dn 11 number 3011 label In Line 01 description Bulldog name Bulldog ! ! ephone-dn 12 number 3012 label In Line 02 description Free FXO name Free FXO ! ! ephone 1 mac-address 0003.6BDD.3B32 speed-dial 1 3010 label "Page House" paging-dn 10 type 7960 button 1:1 2:11 3:12 ! ! ! ephone 2 mac-address 0030.94C3.3F9F speed-dial 1 3010 label "Page House" paging-dn 10 type 7960 button 1:2 2:11 3:12 ! ! ! ephone 3 mac-address 0011.2581.2172 speed-dial 1 3010 label "House Page" button 1:3 2:11 3:12 ! ! ! ephone 4 ! ! ! line con 0 line aux 0 line vty 0 4 exec-timeout 0 0 password 7 login ! ntp clock-period 17180112 ntp source FastEthernet0/0 ntp server 139.143.5.31 prefer end ------------------ show interfaces ------------------ FastEthernet0/0 is up, line protocol is up Hardware is PQUICC_FEC, address is 0011.216c.9511 (bia 0011.216c.9511) Internet address is 172.16.1.11/24 MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, 100BaseTX/FX ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:04, output 00:00:04, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 1000 bits/sec, 1 packets/sec 21017 packets input, 1792564 bytes Received 5693 broadcasts, 0 runts, 0 giants, 0 throttles 1 input errors, 0 CRC, 0 frame, 1 overrun, 0 ignored 0 watchdog 0 input packets with dribble condition detected 31034 packets output, 2610607 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out Serial0/0 is administratively down, line protocol is down Hardware is PowerQUICC Serial MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation HDLC, loopback not set Keepalive set (10 sec) Last input never, output never, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: weighted fair Output queue: 0/1000/64/0 (size/max total/threshold/drops) Conversations 0/0/256 (active/max active/max total) Reserved Conversations 0/0 (allocated/max allocated) Available Bandwidth 1158 kilobits/sec 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 0 packets input, 0 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 0 packets output, 0 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 output buffer failures, 0 output buffers swapped out 0 carrier transitions DCD=down DSR=down DTR=down RTS=down CTS=down ------------------ show controllers ------------------ Interface FastEthernet0/0 Hardware is PQUICC MPC860P ADDR: 84340BE4, FASTSEND: 8069DB64 DIST ROUTE ENABLED: 0 Route Cache Flag: 11 ADDR_LOW =0x0011216C, ADDR_HIGH =0x00009511, HASH_HIGH =0x00000100, HASH_LOW =0 x00000000 R_DES_ST =0x07683B20, X_DES_ST =0x07683C60, R_BUFF_SIZ=0x00000600, ECNTRL =0 xF0000006 IEVENT =0x00000000, IMASK =0x0A000000, IVEC =0xC0000000, R_DES_ACT=0 x01000000 X_DES_ACT=0x00000000, MII_DATA =0x504A0062, MII_SPEED =0x00000020, R_BOUND =0 x00000600 R_FSTART =0x00000500, X_FSTART =0x00000440, FUN_CODE =0x7F000000, R_CNTRL =0 x00000004 R_HASH =0x7A0005F2 X_CNTRL =0x00000004 HW filtering information: Promiscuous Mode Disabled Software MAC address filter(hash:length/addr/mask/hits): pquicc_fec_instance=0x84341CCC rx ring entries=32, tx ring entries=32 rxring=0x7683B20, rxr shadow=0x84341F24, rx_head=22, rx_tail=0 txring=0x7683C60, txr shadow=0x84341FD8, tx_head=25, tx_tail=25, tx_count=0 RX_RING_ENTRIES status 8000, len 40, buf_ptr 7687740 status 8000, len 40, buf_ptr 7684440 status 8000, len 40, buf_ptr 7686420 status 8000, len 40, buf_ptr 7689D80 status 8000, len 46, buf_ptr 76909E0 status 8000, len 40, buf_ptr 768F060 status 8000, len 46, buf_ptr 76870E0 status 8000, len 40, buf_ptr 7687DA0 status 8000, len 5E, buf_ptr 7688A60 status 8000, len 40, buf_ptr 7686A80 status 8000, len 40, buf_ptr 768FD20 status 8000, len 40, buf_ptr 7690380 status 8000, len 40, buf_ptr 768BD60 status 8000, len 46, buf_ptr 7689720 status 8000, len 40, buf_ptr 768D6E0 status 8000, len 46, buf_ptr 7688400 status 8000, len 40, buf_ptr 768EA00 status 8000, len 19A, buf_ptr 768DD40 status 8000, len 40, buf_ptr 7691040 status 8000, len 40, buf_ptr 768C3C0 status 8000, len 40, buf_ptr 768B0A0 status 8000, len 40, buf_ptr 76890C0 status 8000, len 40, buf_ptr 7685760 status 8000, len 40, buf_ptr 768CA20 status 8000, len 46, buf_ptr 768AA40 status 8000, len 40, buf_ptr 7683DE0 status 8000, len 46, buf_ptr 768F6C0 status 8000, len 40, buf_ptr 768E3A0 status 8000, len F7, buf_ptr 768A3E0 status 8000, len FC, buf_ptr 768B700 status 8000, len 19A, buf_ptr 7685100 status A000, len 60, buf_ptr 7685DC0 TX_RING_ENTRIES status 0, len 5A, buf_ptr 76FB3EA status 0, len 172, buf_ptr 76FF1C2 status 0, len 3C, buf_ptr 76FB66A status 0, len 46, buf_ptr 770C00A status 0, len 46, buf_ptr 770DB8A status 0, len 42, buf_ptr 757296A status 0, len 6E, buf_ptr 76FFF8A status 0, len 46, buf_ptr 7710BAA status 0, len 46, buf_ptr 770142A status 0, len 42, buf_ptr 770AB6A status 0, len 6E, buf_ptr 7702FAA status 0, len 3C, buf_ptr 76FB16A status 0, len 42, buf_ptr 76FEAEA status 0, len 42, buf_ptr 75714CA status 0, len 3C, buf_ptr 756C74A status 0, len 3C, buf_ptr 76FC6AA status 0, len 46, buf_ptr 770FDEA status 0, len 46, buf_ptr 77104CA status 0, len 42, buf_ptr 770822A status 0, len 6E, buf_ptr 77021EA status 0, len 46, buf_ptr 77066AA status 0, len 46, buf_ptr 770520A status 0, len 42, buf_ptr 770E26A status 0, len 6E, buf_ptr 770066A status 0, len 3C, buf_ptr 76FB02A status 0, len 46, buf_ptr 7706D8A status 0, len 42, buf_ptr 770368A status 0, len 6E, buf_ptr 770B92A status 0, len 3C, buf_ptr 756D00A status 0, len 42, buf_ptr 770A48A status 0, len 42, buf_ptr 770F02A status 2000, len 3C, buf_ptr 76FC42A throttled=0, enabled=0, disabled=0 rx_framing_err=0, rx_overflow_err=0, rx_buffer_err=1 rx_no_enp=0, rx_discard=0 tx_one_col_err=0, tx_more_col_err=0, tx_no_enp=0, tx_deferred_err=0 tx_underrun_err=0, tx_late_collision_err=0, tx_loss_carrier_err=0 tx_exc_collision_err=0, tx_buff_err=0, fatal_tx_err=0 PHY registers: Register 00 3100 Register 01 782D Register 02 0013 Register 03 78E2 Register 04 01E1 Register 05 41E1 Register 06 0007 Register 16 0184 Register 17 4780 Register 18 0062 Register 19 0000 Register 20 4732 Interface Serial0/0 Hardware is PowerQUICC MPC860 No serial cable attached idb at 0x843CD7F4, driver data structure at 0x843D4F40 SCC Registers: General [GSMR]=0x2:0x00000000, Protocol-specific [PSMR]=0x8 Events [SCCE]=0x0000, Mask [SCCM]=0x0000, Status [SCCS]=0x00 Transmit on Demand [TODR]=0x0, Data Sync [DSR]=0x7E7E Interrupt Registers: Config [CICR]=0x00365F80, Pending [CIPR]=0x00000042 Mask [CIMR]=0x00300000, In-srv [CISR]=0x00000000 Command register [CR]=0x500 Port A [PADIR]=0x0100, [PAPAR]=0x0903 [PAODR]=0x0000, [PADAT]=0xD8FB Port B [PBDIR]=0x0180F, [PBPAR]=0x0F00E [PBODR]=0x00000, [PBDAT]=0x01FEC Port C [PCDIR]=0x000, [PCPAR]=0x000 [PCSO]=0x030, [PCDAT]=0xDFC, [PCINT]=0x000 Receive Ring rmd(FF003030): status 9000 length 60C address 75C1524 rmd(FF003038): status 9000 length 60C address 75C0EA4 rmd(FF003040): status 9000 length 60C address 75C0824 rmd(FF003048): status 9000 length 60C address 75C01A4 rmd(FF003050): status 9000 length 60C address 75BFB24 rmd(FF003058): status 9000 length 60C address 75BF4A4 rmd(FF003060): status 9000 length 60C address 75BEE24 rmd(FF003068): status 9000 length 60C address 75BE7A4 rmd(FF003070): status 9000 length 60C address 75BE124 rmd(FF003078): status 9000 length 60C address 75BDAA4 rmd(FF003080): status 9000 length 60C address 75BD424 rmd(FF003088): status 9000 length 60C address 75BCDA4 rmd(FF003090): status 9000 length 60C address 75BC724 rmd(FF003098): status 9000 length 60C address 75BC0A4 rmd(FF0030A0): status 9000 length 60C address 75BBA24 rmd(FF0030A8): status B000 length 60C address 75BB3A4 Transmit Ring tmd(FF0030B0): status 0 length CAFE address 0 tmd(FF0030B8): status 0 length CAFE address 0 tmd(FF0030C0): status 0 length CAFE address 0 tmd(FF0030C8): status 0 length CAFE address 0 tmd(FF0030D0): status 0 length CAFE address 0 tmd(FF0030D8): status 0 length CAFE address 0 tmd(FF0030E0): status 0 length CAFE address 0 tmd(FF0030E8): status 0 length CAFE address 0 tmd(FF0030F0): status 0 length CAFE address 0 tmd(FF0030F8): status 0 length CAFE address 0 tmd(FF003100): status 0 length CAFE address 0 tmd(FF003108): status 0 length CAFE address 0 tmd(FF003110): status 0 length CAFE address 0 tmd(FF003118): status 0 length CAFE address 0 tmd(FF003120): status 0 length CAFE address 0 tmd(FF003128): status 2000 length CAFE address 0 tx_limited=1(2) SCC GENERAL PARAMETER RAM (at 0xFF003C00) Rx BD Base [RBASE]=0x3030, Fn Code [RFCR]=0x18 Tx BD Base [TBASE]=0x30B0, Fn Code [TFCR]=0x18 Max Rx Buff Len [MRBLR]=1548 Rx State [RSTATE]=0x0, BD Ptr [RBPTR]=0x3030 Tx State [TSTATE]=0x4000, BD Ptr [TBPTR]=0x30B0 SCC HDLC PARAMETER RAM (at 0xFF003C38) CRC Preset [C_PRES]=0xFFFF, Mask [C_MASK]=0xF0B8 Errors: CRC [CRCEC]=0, Aborts [ABTSC]=0, Discards [DISFC]=0 Nonmatch Addr Cntr [NMARC]=0 Retry Count [RETRC]=0 Max Frame Length [MFLR]=1610 Rx Int Threshold [RFTHR]=0, Frame Cnt [RFCNT]=0 User-defined Address 0000/0000/0000/0000 User-defined Address Mask 0x0000 buffer size 1524 PowerQUICC SCC specific errors: 0 input aborts on receiving flag sequence 0 throttles, 0 enables 0 overruns 0 transmitter underruns 0 transmitter CTS losts ------------------ show controllers t1 ------------------ ------------------ show controllers e1 ------------------ ------------------ show controllers j1 ------------------ ------------------ show ip nbar version ------------------ ------------------ show voice port ------------------ Foreign Exchange Office 2/0 Slot is 0, Sub-unit is 2, Port is 0 Type of VoicePort is FXO Operation State is DORMANT Administrative State is UP No Interface Down Failure Description is Bulldog Noise Regeneration is disabled Non Linear Processing is enabled Non Linear Mute is disabled Non Linear Threshold is -21 dB Music On Hold Threshold is Set to -38 dBm In Gain is Set to 10 dB Out Attenuation is Set to -6 dB Echo Cancellation is enabled Echo Cancellation NLP mute is disabled Echo Cancellation NLP threshold is -21 dB Echo Cancel Coverage is set to 64 ms Echo Cancel worst case ERL is set to 6 dB Playout-delay Mode is set to adaptive Playout-delay Nominal is set to 60 ms Playout-delay Maximum is set to 250 ms Playout-delay Minimum mode is set to default, value 40 ms Playout-delay Fax is set to 300 ms Connection Mode is plar opx Connection Number is 3011 Initial Time Out is set to 10 s Interdigit Time Out is set to 10 s Call Disconnect Time Out is set to 5 s Ringing Time Out is set to 180 s Wait Release Time Out is set to 5 s Companding Type is u-law Region Tone is set for GB Analog Info Follows: Currently processing none Maintenance Mode Set to None (not in mtc mode) Number of signaling protocol errors are 0 Impedance is set to 600r Ohm Station name None, Station number None Translation profile (Incoming): Translation profile (Outgoing): Voice card specific Info Follows: Signal Type is loopStart Battery-Reversal is enabled Number Of Rings is set to 1 Supervisory Disconnect is dualtone mid-call Answer Supervision is inactive Hook Status is On Hook Ring Detect Status is inactive Ring Ground Status is inactive Tip Ground Status is inactive Dial Out Type is dtmf Digit Duration Timing is set to 100 ms InterDigit Duration Timing is set to 100 ms Pulse Rate Timing is set to 10 pulses/second InterDigit Pulse Duration Timing is set to 750 ms Percent Break of Pulse is 65 percent GuardOut timer is 2000 ms Minimum ring duration timer is 125 ms Hookflash-in Timing is set to 600 ms Hookflash-out Timing is set to 400 ms Supervisory Disconnnct Timing is set to 350 ms OPX Ring Wait Timing is set to 6000 ms Foreign Exchange Office 2/1 Slot is 0, Sub-unit is 2, Port is 1 Type of VoicePort is FXO Operation State is DORMANT Administrative State is UP No Interface Down Failure Description is Free FXO Noise Regeneration is disabled Non Linear Processing is enabled Non Linear Mute is disabled Non Linear Threshold is -21 dB Music On Hold Threshold is Set to -38 dBm In Gain is Set to 10 dB Out Attenuation is Set to -6 dB Echo Cancellation is enabled Echo Cancellation NLP mute is disabled Echo Cancellation NLP threshold is -21 dB Echo Cancel Coverage is set to 64 ms Echo Cancel worst case ERL is set to 6 dB Playout-delay Mode is set to adaptive Playout-delay Nominal is set to 60 ms Playout-delay Maximum is set to 250 ms Playout-delay Minimum mode is set to default, value 40 ms Playout-delay Fax is set to 300 ms Connection Mode is plar opx Connection Number is 3012 Initial Time Out is set to 10 s Interdigit Time Out is set to 10 s Call Disconnect Time Out is set to 5 s Ringing Time Out is set to 180 s Wait Release Time Out is set to 5 s Companding Type is u-law Region Tone is set for GB Analog Info Follows: Currently processing none Maintenance Mode Set to None (not in mtc mode) Number of signaling protocol errors are 0 Impedance is set to 600r Ohm Station name None, Station number None Translation profile (Incoming): Translation profile (Outgoing): Voice card specific Info Follows: Signal Type is loopStart Battery-Reversal is enabled Number Of Rings is set to 1 Supervisory Disconnect is dualtone mid-call Answer Supervision is inactive Hook Status is On Hook Ring Detect Status is inactive Ring Ground Status is inactive Tip Ground Status is inactive Dial Out Type is dtmf Digit Duration Timing is set to 100 ms InterDigit Duration Timing is set to 100 ms Pulse Rate Timing is set to 10 pulses/second InterDigit Pulse Duration Timing is set to 750 ms Percent Break of Pulse is 65 percent GuardOut timer is 2000 ms Minimum ring duration timer is 125 ms Hookflash-in Timing is set to 600 ms Hookflash-out Timing is set to 400 ms Supervisory Disconnnct Timing is set to 350 ms OPX Ring Wait Timing is set to 6000 ms Foreign Exchange Station 3/0 Slot is 0, Sub-unit is 3, Port is 0 Type of VoicePort is FXS Operation State is DORMANT Administrative State is UP No Interface Down Failure Description is not set Noise Regeneration is enabled Non Linear Processing is enabled Non Linear Mute is disabled Non Linear Threshold is -21 dB Music On Hold Threshold is Set to -38 dBm In Gain is Set to 0 dB Out Attenuation is Set to 3 dB Echo Cancellation is enabled Echo Cancellation NLP mute is disabled Echo Cancellation NLP threshold is -21 dB Echo Cancel Coverage is set to 64 ms Echo Cancel worst case ERL is set to 6 dB Playout-delay Mode is set to adaptive Playout-delay Nominal is set to 60 ms Playout-delay Maximum is set to 250 ms Playout-delay Minimum mode is set to default, value 40 ms Playout-delay Fax is set to 300 ms Connection Mode is normal Connection Number is not set Initial Time Out is set to 10 s Interdigit Time Out is set to 10 s Call Disconnect Time Out is set to 60 s Supervisory Disconnect Time Out is set to 750 ms Ringing Time Out is set to 180 s Wait Release Time Out is set to 30 s Companding Type is u-law Region Tone is set for GB Analog Info Follows: Currently processing none Maintenance Mode Set to None (not in mtc mode) Number of signaling protocol errors are 0 Impedance is set to 600r Ohm Station name None, Station number None Translation profile (Incoming): Translation profile (Outgoing): Voice card specific Info Follows: Signal Type is loopStart Ring Frequency is 25 Hz Hook Status is On Hook Ring Active Status is inactive Ring Ground Status is inactive Tip Ground Status is active Digit Duration Timing is set to 100 ms InterDigit Duration Timing is set to 100 ms Hookflash-in Timing is set to max=1000 ms, min=150 ms Hookflash-out Timing is set to 400 ms No disconnect acknowledge Ring Cadence is defined by Cadence Pattern12 Ring Cadence are [4 2] [4 26] * 100 msec Ringer Equivalence Number is set to 1 Foreign Exchange Station 3/1 Slot is 0, Sub-unit is 3, Port is 1 Type of VoicePort is FXS Operation State is DORMANT Administrative State is UP No Interface Down Failure Description is not set Noise Regeneration is enabled Non Linear Processing is enabled Non Linear Mute is disabled Non Linear Threshold is -21 dB Music On Hold Threshold is Set to -38 dBm In Gain is Set to 0 dB Out Attenuation is Set to 3 dB Echo Cancellation is enabled Echo Cancellation NLP mute is disabled Echo Cancellation NLP threshold is -21 dB Echo Cancel Coverage is set to 64 ms Echo Cancel worst case ERL is set to 6 dB Playout-delay Mode is set to adaptive Playout-delay Nominal is set to 60 ms Playout-delay Maximum is set to 250 ms Playout-delay Minimum mode is set to default, value 40 ms Playout-delay Fax is set to 300 ms Connection Mode is normal Connection Number is not set Initial Time Out is set to 10 s Interdigit Time Out is set to 10 s Call Disconnect Time Out is set to 60 s Supervisory Disconnect Time Out is set to 750 ms Ringing Time Out is set to 180 s Wait Release Time Out is set to 30 s Companding Type is u-law Region Tone is set for US Analog Info Follows: Currently processing none Maintenance Mode Set to None (not in mtc mode) Number of signaling protocol errors are 0 Impedance is set to 600r Ohm Station name None, Station number None Translation profile (Incoming): Translation profile (Outgoing): Voice card specific Info Follows: Signal Type is loopStart Ring Frequency is 25 Hz Hook Status is On Hook Ring Active Status is inactive Ring Ground Status is inactive Tip Ground Status is active Digit Duration Timing is set to 100 ms InterDigit Duration Timing is set to 100 ms Hookflash-in Timing is set to max=1000 ms, min=150 ms Hookflash-out Timing is set to 400 ms No disconnect acknowledge Ring Cadence is defined by CPTone Selection Ring Cadence are [20 40] * 100 msec Ringer Equivalence Number is set to 1 EFXS 50/0/1 Slot is 50, Sub-unit is 0, Port is 1 Type of VoicePort is EFXS Operation State is DORMANT Administrative State is UP No Interface Down Failure Description is not set Noise Regeneration is enabled Non Linear Processing is enabled Non Linear Mute is disabled Non Linear Threshold is -21 dB Music On Hold Threshold is Set to -38 dBm In Gain is Set to 0 dB Out Attenuation is Set to 0 dB Echo Cancellation is enabled Echo Cancellation NLP mute is disabled Echo Cancellation NLP threshold is -21 dB Echo Cancel Coverage is set to 8 ms Echo Cancel worst case ERL is set to 6 dB Playout-delay Mode is set to adaptive Playout-delay Nominal is set to 60 ms Playout-delay Maximum is set to 250 ms Playout-delay Minimum mode is set to default, value 40 ms Playout-delay Fax is set to 300 ms Connection Mode is normal Connection Number is not set Initial Time Out is set to 10 s Interdigit Time Out is set to 4 s Call Disconnect Time Out is set to 60 s Ringing Time Out is set to 180 s Wait Release Time Out is set to 30 s Companding Type is u-law Region Tone is set for US Station name 3001, Station number 3001 Caller ID Info Follows: Standard BELLCORE Translation profile (Incoming): Translation profile (Outgoing): Digit Duration Timing is set to 100 ms EFXS 50/0/2 Slot is 50, Sub-unit is 0, Port is 2 Type of VoicePort is EFXS Operation State is DORMANT Administrative State is UP No Interface Down Failure Description is not set Noise Regeneration is enabled Non Linear Processing is enabled Non Linear Mute is disabled Non Linear Threshold is -21 dB Music On Hold Threshold is Set to -38 dBm In Gain is Set to 0 dB Out Attenuation is Set to 0 dB Echo Cancellation is enabled Echo Cancellation NLP mute is disabled Echo Cancellation NLP threshold is -21 dB Echo Cancel Coverage is set to 8 ms Echo Cancel worst case ERL is set to 6 dB Playout-delay Mode is set to adaptive Playout-delay Nominal is set to 60 ms Playout-delay Maximum is set to 250 ms Playout-delay Minimum mode is set to default, value 40 ms Playout-delay Fax is set to 300 ms Connection Mode is normal Connection Number is not set Initial Time Out is set to 10 s Interdigit Time Out is set to 4 s Call Disconnect Time Out is set to 60 s Ringing Time Out is set to 180 s Wait Release Time Out is set to 30 s Companding Type is u-law Region Tone is set for US Station name 3002, Station number 3002 Caller ID Info Follows: Standard BELLCORE Translation profile (Incoming): Translation profile (Outgoing): Digit Duration Timing is set to 100 ms EFXS 50/0/3 Slot is 50, Sub-unit is 0, Port is 3 Type of VoicePort is EFXS Operation State is UP Administrative State is UP No Interface Down Failure Description is not set Noise Regeneration is enabled Non Linear Processing is enabled Non Linear Mute is disabled Non Linear Threshold is -21 dB Music On Hold Threshold is Set to -38 dBm In Gain is Set to 0 dB Out Attenuation is Set to 0 dB Echo Cancellation is enabled Echo Cancellation NLP mute is disabled Echo Cancellation NLP threshold is -21 dB Echo Cancel Coverage is set to 8 ms Echo Cancel worst case ERL is set to 6 dB Playout-delay Mode is set to adaptive Playout-delay Nominal is set to 60 ms Playout-delay Maximum is set to 250 ms Playout-delay Minimum mode is set to default, value 40 ms Playout-delay Fax is set to 300 ms Connection Mode is normal Connection Number is not set Initial Time Out is set to 10 s Interdigit Time Out is set to 4 s Call Disconnect Time Out is set to 60 s Ringing Time Out is set to 180 s Wait Release Time Out is set to 30 s Companding Type is u-law Region Tone is set for US Station name 3003, Station number 3003 Caller ID Info Follows: Standard BELLCORE Translation profile (Incoming): Translation profile (Outgoing): Digit Duration Timing is set to 100 ms EFXS 50/0/10 Slot is 50, Sub-unit is 0, Port is 10 Type of VoicePort is EFXS Operation State is DORMANT Administrative State is UP No Interface Down Failure Description is not set Noise Regeneration is enabled Non Linear Processing is enabled Non Linear Mute is disabled Non Linear Threshold is -21 dB Music On Hold Threshold is Set to -38 dBm In Gain is Set to 0 dB Out Attenuation is Set to 0 dB Echo Cancellation is enabled Echo Cancellation NLP mute is disabled Echo Cancellation NLP threshold is -21 dB Echo Cancel Coverage is set to 8 ms Echo Cancel worst case ERL is set to 6 dB Playout-delay Mode is set to adaptive Playout-delay Nominal is set to 60 ms Playout-delay Maximum is set to 250 ms Playout-delay Minimum mode is set to default, value 40 ms Playout-delay Fax is set to 300 ms Connection Mode is normal Connection Number is not set Initial Time Out is set to 10 s Interdigit Time Out is set to 4 s Call Disconnect Time Out is set to 60 s Ringing Time Out is set to 180 s Wait Release Time Out is set to 30 s Companding Type is u-law Region Tone is set for US Station name IP-Paging1, Station number 3010 Caller ID Info Follows: Standard BELLCORE Translation profile (Incoming): Translation profile (Outgoing): Digit Duration Timing is set to 100 ms EFXS 50/0/11 Slot is 50, Sub-unit is 0, Port is 11 Type of VoicePort is EFXS Operation State is DORMANT Administrative State is UP No Interface Down Failure Description is not set Noise Regeneration is enabled Non Linear Processing is enabled Non Linear Mute is disabled Non Linear Threshold is -21 dB Music On Hold Threshold is Set to -38 dBm In Gain is Set to 0 dB Out Attenuation is Set to 0 dB Echo Cancellation is enabled Echo Cancellation NLP mute is disabled Echo Cancellation NLP threshold is -21 dB Echo Cancel Coverage is set to 8 ms Echo Cancel worst case ERL is set to 6 dB Playout-delay Mode is set to adaptive Playout-delay Nominal is set to 60 ms Playout-delay Maximum is set to 250 ms Playout-delay Minimum mode is set to default, value 40 ms Playout-delay Fax is set to 300 ms Connection Mode is normal Connection Number is not set Initial Time Out is set to 10 s Interdigit Time Out is set to 4 s Call Disconnect Time Out is set to 60 s Ringing Time Out is set to 180 s Wait Release Time Out is set to 30 s Companding Type is u-law Region Tone is set for US Station name Bulldog, Station number 3011 Caller ID Info Follows: Standard BELLCORE Translation profile (Incoming): Translation profile (Outgoing): Digit Duration Timing is set to 100 ms EFXS 50/0/12 Slot is 50, Sub-unit is 0, Port is 12 Type of VoicePort is EFXS Operation State is DORMANT Administrative State is UP No Interface Down Failure Description is not set Noise Regeneration is enabled Non Linear Processing is enabled Non Linear Mute is disabled Non Linear Threshold is -21 dB Music On Hold Threshold is Set to -38 dBm In Gain is Set to 0 dB Out Attenuation is Set to 0 dB Echo Cancellation is enabled Echo Cancellation NLP mute is disabled Echo Cancellation NLP threshold is -21 dB Echo Cancel Coverage is set to 8 ms Echo Cancel worst case ERL is set to 6 dB Playout-delay Mode is set to adaptive Playout-delay Nominal is set to 60 ms Playout-delay Maximum is set to 250 ms Playout-delay Minimum mode is set to default, value 40 ms Playout-delay Fax is set to 300 ms Connection Mode is normal Connection Number is not set Initial Time Out is set to 10 s Interdigit Time Out is set to 4 s Call Disconnect Time Out is set to 60 s Ringing Time Out is set to 180 s Wait Release Time Out is set to 30 s Companding Type is u-law Region Tone is set for US Station name Free FXO, Station number 3012 Caller ID Info Follows: Standard BELLCORE Translation profile (Incoming): Translation profile (Outgoing): Digit Duration Timing is set to 100 ms ------------------ show inventory ------------------ NAME: "1760 chassis", DESCR: "1760 chassis, Hw Serial#: 453088369, Hw Revision: 0x500" PID: 1760 , VID: 0x500, SN: FOC08270PX3 (453088369) NAME: "Chassis Slot", DESCR: "1700 Chassis Slot" PID: 1700 Chassis Slot , VID: , SN: NAME: "C1760 Mainboard", DESCR: "C1760 Mainboard" PID: C1760 Mainboard , VID: 0x500, SN: FOC08270PX3 (453088369) NAME: "Daughter card slot:0", DESCR: "1700 DaughterCard Slot" PID: 1700 DaughterCard Slot, VID: , SN: NAME: "WIC/VIC 0", DESCR: "WAN Interface Card - Serial (1T)" PID: WIC-1T= , VID: 1.0, SN: 34090046 NAME: "Serial0/0", DESCR: "PowerQUICC Serial" PID: PowerQUICC Serial , VID: , SN: NAME: "Daughter card slot:1", DESCR: "1700 DaughterCard Slot" PID: 1700 DaughterCard Slot, VID: , SN: NAME: "WIC/VIC 1", DESCR: "E1 (2 Port) Multi-Flex Trunk (Drop&Insert) WAN Daught er Card" PID: VWIC-2MFT-E1-DI= , VID: 1.0, SN: 34244619 NAME: "Daughter card slot:2", DESCR: "1700 DaughterCard Slot" PID: 1700 DaughterCard Slot, VID: , SN: NAME: "WIC/VIC 2", DESCR: "Two port FXO voice interface daughtercard" PID: VIC-2FXO= , VID: 1.1, SN: 26651069 NAME: "voice-port 2/0", DESCR: "Foreign Exchange Office 2/0" PID: Foreign Exchange Office 2/0, VID: , SN: NAME: "voice-port 2/1", DESCR: "Foreign Exchange Office 2/1" PID: Foreign Exchange Office 2/1, VID: , SN: NAME: "Daughter card slot:3", DESCR: "1700 DaughterCard Slot" PID: 1700 DaughterCard Slot, VID: , SN: NAME: "WIC/VIC 3", DESCR: "Two port FXS voice interface daughtercard" PID: VIC-2FXS= , VID: 1.1, SN: 22736705 NAME: "voice-port 3/0", DESCR: "Foreign Exchange Station 3/0" PID: Foreign Exchange Station 3/0, VID: , SN: NAME: "voice-port 3/1", DESCR: "Foreign Exchange Station 3/1" PID: Foreign Exchange Station 3/1, VID: , SN: NAME: "DSP Module Slot 0", DESCR: "Packet Voice DSP Module Slot 0" PID: Packet Voice DSP Module Slot 0, VID: , SN: NAME: "DSP Module 0", DESCR: "Packet Voice DSP Module with 2 C549 DSPs" PID: Packet Voice DSP Module with 2 C549 DSPs, VID: 3.2, SN: ICP072417PR NAME: "DSP Port 0/0", DESCR: "C549" PID: C549 , VID: , SN: NAME: "DSP Port 0/1", DESCR: "C549" PID: C549 , VID: , SN: NAME: "DSP Module Slot 1", DESCR: "Packet Voice DSP Module Slot 1" PID: Packet Voice DSP Module Slot 1, VID: , SN: NAME: "DSP Module 1", DESCR: "Packet Voice DSP Module with 2 C549 DSPs" PID: Packet Voice DSP Module with 2 C549 DSPs, VID: 3.2, SN: ICP070700SJ NAME: "DSP Port 1/0", DESCR: "C549" PID: C549 , VID: , SN: NAME: "DSP Port 1/1", DESCR: "C549" PID: C549 , VID: , SN: NAME: "FastEthernet0/0", DESCR: "PQUICC_FEC" PID: PQUICC_FEC , VID: , SN: Login or register to post comments


	#4Submitted by Hoover87 on Tue, 08/12/2008 - 13:40. Try the following.....use Try the following.....use your ? cause that was off the cuff....don't have the docs infront of me. card type e1 0 controller E1 Cisco IP Communications Express Specialist www.ketchumits.com Login or register to post comments

UC500.com

Configuration Guides

User login

Navigation

Popular content

Today's:

All time:

Last viewed:

Recent comments

Who's online

Online users

Who's new

VWIC-2MFT-E1-DI looks like its dead! Help...

What does 'controller E1

Is there a command to reset

Thanks for the reply. I had

Try the following.....use

Comment viewing options

About londonnet

Syndicate

Popular Tags

Active forum topics

Voice News

Cisco TAC Issues - CME - UE

Archive